Build own extender
- Thread starter Peter Brown II
- Start date
Not yet...
Still waiting
I’ve surged around the internet but then its a page of a profesional extender.
Or the selfmade system looks a bit painfull..
Maybe there is someone over here who has a simple selfmade solution... i hope
I made mine. I knew someone who worked as a machine operator. He told me thdy were throwing out scrap materia and I grabbed a hug block of nylon and delrin. Delrin was what I wanted and I shaped it using a wood hole cutter and a drill. I then drilled 1/2 inch holes in the sides and used scrap 1/2 brass stock to make swival hinges for the aluminum bars I would use as risers. Drill and tap the brass, use a die on the aluminium bars and I was half way there.
Given that there would be wear over time I used thumb tightening screws and replacable delrin scrap to make set screw locks to set the adjusted stretch of the head piece that clamped onto my upper shaft and foreskin. The thumb tightening locks would swivel in a knotched out groove on each side of the tracks, allowing room to tighten and loosen and be hidden under clothing easier. Everything can be sanded down with a dremill. Smooth out the ring base with no bumps or rough edges. The head piece has set screws to snag onto a clamp to keep it in place an no slippage. I wrap my dick in a neoprene belt from a knee strap for a cushion which should fit easy into a curved groove where you rest your member in. I wear it 8 hours a day on average.
You can see the design here...
https://www.lpsg.com/threads/extender-schedule-throughout-day-changes.484309/
If you hand tighten the securing clamp with a neoprene sleeve it doesn't hurt, but uncomfortable after some hours. Take it off every hour to help blood flow and readjust height. After a while you get an inch stretch difference between morning to evening application as your ligaments get use to the stretch. It just takes time.
Given that there would be wear over time I used thumb tightening screws and replacable delrin scrap to make set screw locks to set the adjusted stretch of the head piece that clamped onto my upper shaft and foreskin. The thumb tightening locks would swivel in a knotched out groove on each side of the tracks, allowing room to tighten and loosen and be hidden under clothing easier. Everything can be sanded down with a dremill. Smooth out the ring base with no bumps or rough edges. The head piece has set screws to snag onto a clamp to keep it in place an no slippage. I wrap my dick in a neoprene belt from a knee strap for a cushion which should fit easy into a curved groove where you rest your member in. I wear it 8 hours a day on average.
You can see the design here...
https://www.lpsg.com/threads/extender-schedule-throughout-day-changes.484309/
If you hand tighten the securing clamp with a neoprene sleeve it doesn't hurt, but uncomfortable after some hours. Take it off every hour to help blood flow and readjust height. After a while you get an inch stretch difference between morning to evening application as your ligaments get use to the stretch. It just takes time.
I am going to draw one up and print one out the parts on my 3d printer.
jamaicanstalion
Cherished Member
- Joined
- Feb 1, 2013
- Posts
- 85
- Media
- 24
- Likes
- 455
- Points
- 138
- Location
- Kingston, Saint Andrew, Jamaica
- Sexuality
- 100% Straight, 0% Gay
- Gender
- Male
i just use a resistance band and use it like a stretcher
There are so many decent knock offs that are cheap but well made why bother making your own? You can get good ones off ebay for 20 bucks.
jamaicanstalion
Cherished Member
- Joined
- Feb 1, 2013
- Posts
- 85
- Media
- 24
- Likes
- 455
- Points
- 138
- Location
- Kingston, Saint Andrew, Jamaica
- Sexuality
- 100% Straight, 0% Gay
- Gender
- Male
I agree with big Sam, I just use the resistance band cause I have it here already but with knock off technology at the level it is might as well purchase something.
Similar threads
